1)江苏南京某电子废水处理工程 工艺流程:均质+氧化还原+重金属捕集+絮凝沉淀+超滤+反渗透 装卸能力:1500吨/天 2)河北洛阳某废水处理工程 工艺流程:格栅+高效气浮、水解酸化、生物接触氧化+絮凝+深度过滤。 装卸能力:2400吨/天 3)山西长治某制药废水处理工程 工艺流程:均质+水解+生物接触氧化+絮凝沉淀+深层过滤 装卸能力:500吨/天 污水处理设备工艺分析 小区污水处理设备是埋藏在地表以下。设备表面可以绿化。不需要建筑物、暖气和热处理。下设备5T/H可采用玻璃钢或A3钢板。采用曝气2,两级生物接触氧化工艺,活性污泥,体积小,对水质适应性好,水质稳定,不产生污泥膨胀。 沉淀池是接触氧化槽的支撑设施,用来分离污泥和混合物。该方案采用四斗沉淀池。选用四桶沉淀池可减少空间高度,便于排泥。沉淀池的表面负荷为0.8 m2 h,沉淀时间为2小时。通过污泥泵或真空吸粪车提取污泥中的污泥斗的沉积,为污泥回流调节池的一部分,其他排到浓缩污泥消化池。沉淀池排出的污水流入消毒池。设计参数:沉淀池:1号;停留时间2h;钢。 今后,我们将继续以“保护环境造福人类”为宗旨,坚持以诚实守信为原则,遵循做事的**原则,坚持“飞跃、不断创新、以*的质量、以不变的质量、奉献给客户满意”的“针”。 济宁天通设备有限公司全体员工热忱欢迎尊敬的用户、各界朋友前来参观、洽谈业务!我们愿与中外朋友精诚合作,共谋环保事业,打造高标准环保制造设计企业。 Analysis of wastewater treatment process The sewage treatment equipment in the district is buried below the surface. The surface of the equipment can be greening. There is no need for buildings, heating and heat treatment. The lower equipment 5T/H can be made of fiberglass or A3 steel. Using aeration 2, two stage biological contact oxidation process, activated sludge, small volume, good adaptability to water quality, stable water quality, do not produce sludge bulking. The sedimentation tank is a supporting facility to contact the oxidation tank, which is used to separate the sludge and the mixture. The scheme uses four bucket sedimentation tanks. The selection of four bucket sedimentation tanks can reduce the space height and facilitate the sludge discharge. The surface load of the sedimentation tank is 0.8 M2 h, and the precipitation time is 2 hours. Extraction of sludge in the sludge deposition truck bucket by sludge pump or vacuum, as part of a sludge return regulation pool, the other row to the concentrated sludge digestion tank. The sewage discharged from the sedimentation tank flows into the sterilizing pool. Design parameters: sedimentation tank: No. 1; residence time 2H; steel.